Blog Post

How Sediment Can Damage Your Hot Water Heater And How To Flush It From Your Tank

  • By Paul Armand Abecilla
  • 02 Feb, 2018

HOW SEDIMENT CAN DAMAGE YOUR HOT WATER HEATER AND HOW TO FLUSH IT FROM YOUR TANK

Your water heater is the most used appliance in your home, next to the refrigerator. That's why it needs periodic maintenance to keep functioning reliably; otherwise, the effects of time and usage will eventually cause your water heater to fail.


Specifically, the most important maintenance step to take with a water heater is to flush it annually. Flushing removes harmful sediments that will not only prevent your water heater from doing its job but also cause permanent damage. Below is more information on why flushing is necessary and how to perform the job at home.

HOW SEDIMENTATION CAN DAMAGE YOUR WATER HEATER

Though tap water may appear to be pure, it actually contains numerous dissolved elements. Many of these invisible substances will pass through your water heater and plumbing, but some will precipitate from the water and form tiny flecks of material inside the water heater.


Calcium and magnesium are two such elements that emerge as sediments during the heating process. Each piece of sediment is small, but together they create a substantial pile as they accumulate at the bottom of your water heater.


Whether your water heater is electric or gas-powered, sediments form an insulating barrier between the heat source and the water inside the tank. As a result, the water is no longer as hot as it should be, and the water heater's tank absorbs the unused heat that was intended for the water. Too much heat can damage the metal and shorten the lifespan of your water heater.

HOW TO PERFORM A HOT WATER HEATER FLUSH

The solution to sedimentation is fairly straightforward, as your water heater is equipped with a readymade device to help you eliminate excess sediment. Below is how to perform an annual flush of your water heater and remove damaging sediment accumulation.


1. Turn off the heat source of your water heater
Begin by disconnecting the electrical current to an electric water heater or turn off the gas supply valve for a gas-fired unit. Do not rely on the thermostat alone, as the water heater may accidentally turn itself on again during flushing.


2. Connect a water hose to the drain fitting
At the bottom of your water heater is a drain fitting that resembles a spigot or garden tap. Screw the female fitting of a garden hose onto the drain fitting and tighten the connection by hand. Unfurl the garden hose and route it toward a location where hot water drainage won't cause any harm.


3. Drain the water heater
Once the garden hose is connected, and it's routed to an appropriate spot, open the drain valve by turning the handle counterclockwise. Next, walk to the end of the garden hose and keep an eye on the stream of water leaving the hose. You will notice an accumulation of white, tan or gray sediment on the ground beneath the hose.


Allow the water heater to continue flushing until pieces of sediment stop appearing. Once you are satisfied that enough sediment has evacuated the tank, turn off the drain valve and disconnect the garden hose.


4. Restart the water heater
When you have removed the garden hose from the valve, reconnect the electrical current or gas supply to the water heater. Consult the instructions on relighting the water heater, which is likely located on the exterior of the tank itself, or may be found online on the manufacturer's website.
If you have questions about flushing your water heater or need to replace an aging unit, be sure to contact Superdrain for assistance. Their professionals are ready to assist you with whatever water heater needs you may have and can provide expert advice on replacement options.

By Paul Armand Abecilla 03 Dec, 2017

When a drain clogs or slows down, you probably plunge it a little or use some drain cleaner to free the blockage. While these measures provide a short-term solution, you might find that the blockage reappears before long. This is because, when clogs reoccur, there is often a bigger underlying issue at fault.


A smarter way to fight clogs and blockages is to identify this root cause and address it. Not only will this clear your immediate clogs, but it will also prevent future ones. Here are four of the most common underlying causes of clogs and how to address them.

By Paul Armand Abecilla 04 Oct, 2017

If you have a slab foundation, chances are you keep a look out for any potential signs of problems. However, there is one often-overlooked issue that could lead to costly damage, and learning to recognize the signs of this issue is critical. If left untreated, even a minor slab leak can lead to a host of potentially dangerous problems, including mildew growth and damage to your home's wooden support structure.


It is critical that you learn to recognize the signs of a slab leak to ensure that no further damage occurs. Here are a few of the most common signs that you have a concrete slab leak.

By Paul Armand Abecilla 07 Aug, 2017

Whether you've had a suspiciously high utility bill this month or you've noticed that areas of your home are extra-damp, humid and musty, the suspicion that you could have a water leak somewhere in your plumbing system can be infuriating—especially if you're having a hard time pinning it down.


There are a few things you can take to try and locate the leak on your own, but sometimes water leaks will occur inside your walls in inaccessible locations. That would explain why you're having such trouble finding the leak. Here are some steps to take to find a leak in your plumbing.

By Paul Armand Abecilla 27 Mar, 2017
Even the most reliable plumbing fixtures and equipment have a limited life span. However, with a complicated item like a water heater, it may not always be obvious when you need a replacement.
By Paul Armand Abecilla 23 Feb, 2017
Some home remodeling and construction projects are DIY-friendly, like painting or adding insulation to your attic. Plumbing tasks, however, are not something to be handled without knowledge and experience. It's not wise to try replacing a pipe or cleaning a sewer line yourself, and you should not hire an inexperienced individual to tackle these tasks, either. But why is hiring an experienced, licensed plumber so important? Here's a look:
Share by: